Cable Connection’s on ESXI – Switching Topology using Cisco Vios

Today, I will show you how to make cable connection between the switches using ESXi.

I could not find a proper document and hence I thought I will write this article so that this might help the other engineers  using ESXi to build the virtual topologies more effectively.

I am using Vios-L2 image for this demo. Please do not ask me for this image and I am not going to SHARE this.

I am currenlty labbing from the Narbik Workbook.  Please visit http://www.micronicstraining.com/ for their Workbook material.

Featured image

I am going to show you how you can make the above topology virtually. The CCIE R n S version 5 is Vitual and hence I thought of implementing the same.

Looking at the above diagram, we see that we would need 4 x Virtual-Switches and 13 cables to interconnect them.

Let’s get Started

First we will create cable connection so that we can connect between the switches.

In order to do that, select ESXi host and then go to Configuration tab and then click Add Networking as shown below.

Featured image

Featured image

Once you click Add Networking, follow the below procedure as shown below.

Featured image

Select Virtual Machine and click NEXT

Featured image

Make sure you un-select the VMNIC-0 as we just need a cable type connection so that we can connect two switches.

Featured image

Once you un-select, hit Next.

Featured image

Give a meaning Full Name to the Network Label and Select Vlan-ID (4095) and hit Next.Featured image

Now Click FINISH.

If you look under the configuration tab, you will see that the network connection is created and there is no adapters connected to it.

Featured image

Using the above procedure, I have created 13 such connections.

I have connected 4 switches as per the below diagram.

Featured image

If we examine the Network adapter settings for Sw-1, you should set it like below.

Featured image

SW-2 Network Adapter settings :

Featured image

SW-3 Network Adapter settings :

Featured image

SW-4 Network Adapter settings :

Featured image

Please note that the network adapters on these switches starts from G0/0 onwards.

Network Adapter 1 indicates its G0/0,

Network Adapter 2 indicates its G0/1,

Network Adapter 3 indicates its G0/2,

Network Adapter 4 indicates its G0/3,

Network Adapter 5 indicates its G1/0,

Network Adapter 6 indicates its G1/1,

Network Adapter 7 indicates its G1/2,

Network Adapter 8 indicates its G1/3,

Network Adapter 9 indicates its G2/0,

Network Adapter 10 indicates its G2/1.

As per my Understanding Cisco Vios images supports upto 10 Network Adapters. I might be wrong.

Let me start the switches and see what show CDP neighbor tells us 🙂

On SW-1 :

Featured image

On SW-2

Featured image

On SW-3

Featured image

On SW-4

Featured image

I will write another post in future with all the labs I do successfully on Vios-L2.

If you are using Vmware WorkStation then you can only make 19 connections and that is the maximum it supports.

I believe ESXi supports 120 connections which is more than enough for us to do the labs.

8 thoughts on “Cable Connection’s on ESXI – Switching Topology using Cisco Vios

  1. Pingback: Cable Connection’s on ESXI – Switching Topology using Cisco Vios | aftabmemon
  2. Hi,
    How do you telnet to the switch? i notice you configure serial as 192.168.1.50:2031. I didnt the same configuration. But wasnt able to reach the ip. I’m using 192.168.x.x network. I use telnet 192.168.1.240:2030

  3. Pingback: Cable Connection’s on ESXI – Switching Topology using Cisco Vios – MamLab – Network Consultant

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s